Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 release

Repair and operation of the car

Toyota Land Cruiser, Amazon, Lexus LX470
+ Identification numbers of the car
+ Governing bodies and methods of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Cooling systems of the engine, heating of salon and air conditioning
+ A power supply system and production of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear shifting box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative front grille
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation flew down also the back door window regulator regulator
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of latches, castle cylinders and door handles
   Removal and installation of a cover of the top hatch with the drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main dashboards of sections
   Removal and installation of a lattice of an air inlet of a forward fairing
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment


Removal and installation of a cover of the top hatch with the drive

At removal of internal overlays of an upholstery stock up with various clip-on earrings – ри removal they often break.

Arrangement of elements of management of a cover of the top hatch


1. Remove the following components:

  • Overlay of a threshold of a door of a back;
  • Back seat;
  • Left and right side upholstery;
  • Side overlay of a back seat;
  • Overlay of a threshold of a back door;
  • Forward lower side slip;
  • Facings of an aperture of a forward and back door;
  • Lower overlay of the central rack;
  • Humeral clamp (anchor) of a seat belt of a front seat;
  • Top facing of the central rack;
  • The seat belt regulator on height;
  • Both external clamps (anchor) of seat belts of a back seat;
  • Overlay of the third rack;
  • Overlay of a back rack;
  • Top handles;
  • Overlay of a forward rack and peaks with arms;
  • Internal rear-view mirror;
  • Forward and back lamps of illumination of salon;
  • Facing of a doorway of a back;
  • Molding of the top hatch;

2. Remove the switch of management, having uncovered. Unfasten a cover from the case, turn off fastening of the switch. Separate the socket and remove the switch with an arm (address an illustration above).
3. Remove clip-on earrings of fastening of the panel of a ceiling.
4. Dismantle the relay of control of the drive of a cover of the top hatch and disconnect from it the socket.
5. Turn off bolts of fastening of the drive with an arm. Remove the drive and separate the socket.
6. Remove overlays of the hatch. Having hooked from the inside, unhook clip-on earrings of slips.
7. Remove hatch glass. Turn off nuts and remove washers. In total there have to be six washers. Glass is removed up.
8. Remove the drive tunnel.
9. Remove a vetrootboynik.
10. Disconnect a drainage hose and remove the hatch cover case.
11. Adjust a trench of the drive of a cover of the hatch. The screw-driver shift draft forward or back for combination of two tags.
12. Adjust and establish drive knot as follows:

   a. Unscrew the screw and uncover a cam plate;
   b. Unscrew the big screw, remove washers;
   c. Turn a power shaft the screw-driver so that to combine dot tags on the case and a gear wheel;
   d. Establish a cover of a cam plate, having fixed it by the screw;
   e. Establish knot of the drive and fix by four bolts;
   f. Attach the socket.

13. Install the relay of control of the drive together with an arm, attach the socket.
14. Establish the remained details as it should be, the return to removal.