Toyota Land Cruiser, Amazon, Lexus LX470 + Identification numbers of the car + Governing bodies and methods of safe operation of the car + Settings and routine maintenance of the car + Engine + Cooling systems of the engine, heating of salon and air conditioning + A power supply system and production of the fulfilled gases + Engine electric equipment + Control systems of the engine and decrease in toxicity of the fulfilled gases + Gear shifting box + Transmission line + Brake system + Suspension bracket and steering - Body Specifications Care of components of a body and bottom of the car Care of vinyl elements of finishing Care of an upholstery and carpets of salon Repair of insignificant damages of body panels Repair of seriously damaged body panels Service of loops and locks of the car Replacement wind and other fixed glasses Removal, installation and adjustment of provision of a cowl Removal and installation of a latch of the lock of a cowl and cable of its drive Removal and installation of a decorative front grille Removal and installation of forward and back bumpers Removal and installation of panels of an internal upholstery of doors Removal and installation of external rear-view mirrors Removal, installation and adjustment of doors Removal and installation of forward wings Removal, installation and adjustment of a door of a back Removal and installation flew down also the back door window regulator regulator Removal and installation of door glasses Removal and installation of regulators of window regulators Removal and installation of latches, castle cylinders and door handles Removal and installation of a cover of the top hatch with the drive Removal and installation of a casing of a steering column Removal and installation of the central console Removal and installation finishing and main dashboards of sections Removal and installation of a lattice of an air inlet of a forward fairing Removal and installation of seats Removal and installation of an internal rear-view mirror + Onboard electric equipment
|
Removal, installation and adjustment of provision of a cowl
Removal and installation
|
The panel of a cowl has the decent weight therefore it is necessary to get support of the assistant. |
|
1. Open a cowl, then cover wings with special overlays or just old blankets for protection them from damage to process of dismantle of the panel. 2. Disconnect all cables and wires preventing removal of a cowl. Also disconnect brought to the nozzles of a tube of supply of liquid of washing of a windshield fixed in a cowl. 3. A marker or a chertilka lead round loopy levels for a guarantee of correctness of fastening of a cowl at assembly. 4. Ask the assistant to take a cowl and give bolts of fastening of loopy levels. 5. Installation is made upside-down. At installation to the place of an old cowl track that loopy levels were established taking into account the tags put in the course of dismantle (see paragraph 3). If replacement of a cowl is made, it is necessary to make adjustment of its situation (see below). |
|
Adjustment
|
After adjustment of a cowl its given conical bolts need to be replaced with new. |
|
|
1. Adjustment of provision of a cowl in an aperture of a motive compartment is made by shift in the relevant party of loopy levels after weakening of their fixture (address an accompanying illustration).
|
If at manufacturer the self-centering bolts which are not allowing a possibility of carrying out similar adjustment are applied to fastening of levels, such fixture should be replaced with bolts of standard type, without having forgotten to equip them with flat and lock washers. |
|
|
2. Adjustment of height of a first line of a cowl is made by a reversing or a wraparound of rubber support so that the edge of a cowl was flush with wings (address an accompanying illustration). |
3. Height of the rear edge of a cowl is regulated if to weaken four screws of fastening of loops to a partition of a motive compartment.
|
4. Updating of the provision of assembly of a latch of the lock of a cowl on a basic plate of a radiator can be in case of need executed (in the vertical and horizontal planes), the cowl has to be closed densely and fall aflush with the surfaces of wings (address an accompanying illustration). For adjustment of the lock lead round heads of bolts of fastening of assembly of a latch a marker or a chertilka, then weaken bolts and displace a latch in the required direction. Upon completion of adjustment strongly tighten fixing bolts. |
5. Assembly of a latch of the lock of a cowl has to periodically (along with loops, see the Section Service of Loops and Locks of the Car) to be processed by lubricant on a lithium basis in order to avoid jammings and premature wear of components. |
|
|
|