Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 release

Repair and operation of the car



Toyota Land Cruiser, Amazon, Lexus LX470
+ Identification numbers of the car
+ Governing bodies and methods of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Cooling systems of the engine, heating of salon and air conditioning
+ A power supply system and production of the fulfilled gases
+ Engine electric equipment
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ Gear shifting box
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of a decorative front grille
   Removal and installation of forward and back bumpers
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of external rear-view mirrors
   Removal, installation and adjustment of doors
   Removal and installation of forward wings
   Removal, installation and adjustment of a door of a back
   Removal and installation flew down also the back door window regulator regulator
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of latches, castle cylinders and door handles
   Removal and installation of a cover of the top hatch with the drive
   Removal and installation of a casing of a steering column
   Removal and installation of the central console
   Removal and installation finishing and main dashboards of sections
   Removal and installation of a lattice of an air inlet of a forward fairing
   Removal and installation of seats
   Removal and installation of an internal rear-view mirror
+ Onboard electric equipment


08d33331



Removal and installation finishing and main dashboards of sections

The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see. Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.

Dashboard design


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Disconnect safety cushions (see. Onboard electric equipment).
3. Remove a steering wheel (see the Head Podvesk and steering).
4. Remove a casing of a steering column (see the Section Removal and installation of a casing of a steering column).
5. Paste over with a protective film of an overlay of forward racks (address an illustration above), it will protect them at removal.
6. Remove handles of opening of a cowl and the hatch of the fuel tank.
7. Uncover the block of safety locks.
8. Give fixture of the lower central cover and remove it.
9. Disconnect an air duct No. 2.
10. Give fixture of the DLC socket No. 3 and the block of safety locks.
11. Remove the lower panel No. 1.
12. Remove an overlay of a combination of devices and remove a combination of devices.
13. Remove the lower overlay of the central section of finishing of the dashboard together with hours.
14. Having wound the screw-driver with an insulating tape, unhook 2 latches and remove a coaster.
15. Remove an ashtray.
16. Give fixture central section of finishing of the dashboard with the control panel of a heater and disconnect conducting.
17. Turn out screws of fastening of the control panel of a back heater.
18. Remove the radio tape recorder, a cover of a ware box, the panel of a loudspeaker and a loudspeaker, forward and back sections of the central console.
19. Unscrew 5 screws and 9 bolts of fastening of the main section of the dashboard.
20. Remove an intensifying bar, an arm and the main section of the dashboard.
21. Installation is made upside-down.